Benzoylation-Induced Interfacial Enhancement in Cassava Peel–Ldpe Composites with Insights into Morphological, Mechanical and Water Absorption Properties

Authors

  • Okpanachi Baba Clifford Department of Pure and Industrial Chemistry, Prince Abubakar Audu University, Anyigba, Kogi State. Author
    • Sale Friday Department of Pure and Industrial Chemistry, Prince Abubakar Audu University, Anyigba, Kogi State. Author
      • Ameh Ekwu Mark Department of Pure and Industrial Chemistry, Prince Abubakar Audu University, Anyigba, Kogi State. Author
        • Ejukwa Emmanuel Department of Pure and Industrial Chemistry, Prince Abubakar Audu University, Anyigba, Kogi State. Author
          • Ekwoba Lucky Department of Pure and Industrial Chemistry, Prince Abubakar Audu University, Anyigba, Kogi State. Author
            • Ocheme Wilson Department of Pure and Industrial Chemistry, Prince Abubakar Audu University, Anyigba, Kogi State Author
              • Dauda Joseph Abiodun Department of Pure and Industrial Chemistry, Prince Abubakar Audu University, Anyigba, Kogi State. Author

                Keywords:

                Benzoylation, Biocomposites, Cassava peel, Interfacial Adhesion, LDPE, Mechanical properties.

                Abstract

                This study examines the effect of benzoylation surface treatment on the morphological, mechanical, and water absorption properties of cassava peel–reinforced low-density polyethylene (LDPE) composites. Neat LDPE, unbenzoylated composites (UCPLC), and benzoylated composites (BCPLC) were compared. Scanning electron microscopy confirmed the influence of surface treatment, revealing cracks, voids, and filler pull-out in UCPLC, while BCPLC displayed smoother, denser morphologies with minimal interfacial separation. Neat LDPE showed the lowest tensile (21.08 MPa), flexural (13.43 MPa), and compressive strength (9.84 MPa), reflecting its ductility and limited load-bearing capacity. Incorporating cassava peel filler improved strength, with UCPLC reaching 41.87 MPa (tensile) and 26.63 MPa (flexural), though performance declined at higher loadings due to filler agglomeration. BCPLC exhibited consistently superior performance. Tensile strength ranged from 42.67 MPa at 5 wt% to 60.33 MPa at 25 wt%, nearly three times that of neat LDPE, while flexural strength peaked at 41.52 MPa (20 wt%). Compressive strength also improved, reaching 25.56 MPa at 20 wt% and 28.77 MPa at 25 wt%, compared with 19.87 MPa and 16.57 MPa for UCPLC at equivalent loadings. Moisture uptake was substantially reduced by benzoylation. After 10 days, UCPLC absorbed 2.66–5.20% water (5–25 wt%), whereas BCPLC recorded only 1.46–3.04%, compared to 0.44% for neat LDPE. This reduction reflects enhanced filler–matrix adhesion and lower void density. Overall, benzoylation significantly improved compatibility between cassava peel filler and LDPE, yielding composites with superior tensile (60.33 MPa), flexural (41.52 MPa), compressive (28.77 MPa), and water resistance (3.04%) compared to UCPLC and neat LDPE. These results highlight benzoylated cassava peel as a cost-effective reinforcement for high-performance biocomposites.

                Downloads

                Download data is not yet available.

                References

                N

                Additional Files

                Published

                2026-09-20

                Data Availability Statement

                N/A

                Issue

                Section

                Original Research Articles

                How to Cite

                Benzoylation-Induced Interfacial Enhancement in Cassava Peel–Ldpe Composites with Insights into Morphological, Mechanical and Water Absorption Properties. (2026). ChemClass Journal, 9(3), 290-305. https://chemclassjournal.com.ng/index.php/ccj/article/view/181

                Share

                Most read articles by the same author(s)

                Similar Articles

                11-20 of 61

                You may also start an advanced similarity search for this article.